2019 KPI-JCI 33-36150 For Sale

Print Friendly, PDF & Email

KPI 33-36150 Super Stacker For Sale

SPECS:

Main Conveyor:
– Frame – 80′ long c/c w/ 70″ deep frame
– Undercarriage – Heavy duty v-type with twin cylinder raise and cylinder covers; 10 HP electric/hydraulic power pack to operate lift cylinders, power travel drives and extendable conveyor travel
– Axle – gullwing axle assembly. Includes: walking beam travel axle with eight (8) 11-22.5 tires, four (4) 385/65D-19.5 radial travel tires. King pin, air brakes, travel, brake and directional lights, mudflaps, hydraulic planetary power travel drives for four wheel drive
– Cam Arm-Style Rear Undercarriage – to maintain constant wheel radius when raising and lowering conveyor
– Center Heavy Duty Tow Eye – For positioning within pit
– Drive Assembly – Head end, v-belt drive for 425 FPM belt speed; Backstop – internal type in reducer
– Pulleys – Head Pulley 16″ grooved rubber lagged, Dodge bearings, Tail Pulley – 14″ steel wing, Dodge bearings
– Take-Up – Screw type
– Radial Receiving Hopper – (Rock box style) 6′ long with adjustable rubber flashing
– Anchor Pivot – Anchor pivot for radial travel

Extendable Conveyor Equipped as Follows:
– Frame – 74′ long with 54″ deep truss with head section
– Extendable Conveyor – Moves in and out with a cable and hydraulic winch system (winch located in main frame conveyor) to extend the conveyor to 150 feet
– Drive Assembly – Head end, v-belt drive for 630 FPM belt speed; Backstop – Internal type in reducer
– Pulleys – Head Pulley – 16″ grooved rubber lagged, Dodge bearings; Tail Pulley – 14″ steel wing, Dodge bearings
– Take-Up – Screw type
– Electrical – NEMA 4 enclosure with main disconnect mounted on the rear undercarriage member; all starters and wiring to motors; start/stop pushbuttons for main conveyor motor, extendable conveyor motor, hydraulic power pack motor; cord holders and supports for power cable, LESS power cable – 460 Volt, 3 phase, 60 Hz power required

Also Includes:
– Drive Configuration – 1000 TPH; Main conveyor drive consists of a 40 HP, 1800 RPM, TEFC electric motor and a Dodge TA5215 Class I shaft mount reducer; Stinger Conveyor consists of a 30 HP 1800 RPM TEFC electric motor and a Dodge TA4207 Class I shaft mount reducer; 1000 tph of 100 pcf material
– Load Area Idlers – Close spaced troughing idlers; on main conveyor
– Idlers – CEMA C Idlers, 5″ diameter, steel roll, sealed for life ball bearings; 35 degree on 4′ spacing
– Return Idlers – Steel Rolls, 10′ spacing
– Belt – Grade 2, 3 ply; 330 PIW, 3/16″ x 1/16″ covers
– Belt Splices – Mechanical Fasteners
– Landing Jacks – Manual Pin Lock
– Power Radial Travel – Four Wheel Drive; hydraulic Planetary drives; powers two wheels on each side of conveyor
– Gullwing Axle Configuration – Hydraulic Fold Down Cylinders; also includes plumbing; for raising and lowering the radial travel tires on the gullwing axle
– Controls – Wizard Touch; automated control system; includes touch screen PLC operating, allows for either factory pre-set or operator input parameters to control the power travel, conveyor raise and lower, and telescoping of the extendable conveyor; also includes radial travel limit switches and rotation sensor
– Material Flow Sensor – causes power travel to stop when material is not detected on belt

Request More Info

Categories: , Tag:

Additional information

Model Year

2019

Manufacturer

KPI-JCI

Model

33-36150

Serial Number

418703

Condition

Rental

Hours

107

Stock Number

049484